MECHANICAL PROJECTS

Projects of design, analysis and manufacturing

Projects of design, analysis and manufacturing

  1. Design and analysis of army vehicle chassis
  2. Modeling and structural analysis of helicopter landing struct for different materials
  3. Fea analysis of a cargo carrier.
  4. Static & modal analysis of composite bracket assembly.
  5. Modeling and analysis of a leaf spring.
  6. Modeling and analysis of machine tool elements using ug and ansys.
  7. Modeling and analysis of a vertical axis wind turbine blade.
  8. Modeling and analysis of a connecting rod of a diesel engine.
  9. Modelling and analysis of a drum brake.
  10. Stress analysis of crankshaft.
  11. Modelling and analysis of a compressor casing.
  12. Finite element analysis for static and dynamic behaviour of a shaft made of a composite.
  13. Finite element analysis of a navigation compartment of a pressure hull.
  14. Modal analysis of a muffler guard.
  15. Modeling and dynamic analysis of crank case.
  16. Modeling and analysis of a chassis for a 60 ton pay load.
  17. Modeling and analysis of inlet manifold
  18. evaluation of fuselage stringer section by using fea
  19. design and optimization of wind power generator frame for structural loads
  20. modeling and dynamic analysis of vibrator grader
  21. Design and analysis of helicopter rotor hub for structural loads.
  22. Modeling and finite element analysis of engine block
  23. Design optimization of aero plane radome by using FEM.
  24. Modeling and Static analysis of washing machine drum.
  25. Modeling and analysis of hypoid gear.
  26. Modeling and dynamic analysis vibrating screen.
  27. Modeling and static analysis of missile control component
  28. Modeling and analysis of exhaust manifold
  29. Modeling and analysis of helicopter rotor blade
  30. Structural design, dynamic analysis and optimization of engine rocker cover
  31. Heat transfer in the cylinder head of a two-stroke engine
  32. Stress & deflection analysis of horizontal pressure vessel with different dished end using fem.
  33. Modeling and analysis of a master cylinder.
  34. Modeling and analysis of IC engine piston with composite material
  35. Modeling and analysis of a leaf spring.
  36. Modeling and analysis of a disk brake
  37. Finite element analysis of aircraft fuel tank.
  38. Structural analysis of a flatbed
  39. Modeling and dynamic analysis of spur gear.
  40. Modeling and dynamic analysis of helical gear.
  41. Analysis of swinging plate of jaw crusher.
  42. Analysis of pelton wheel bucket.
  43. Modeling and static analysis of lifting beam.
  44. Modeling and analysis of a chassis for a 60 ton pay loads.
  45. Structural Analysis of tillage equipment.
  46. Design and optimization of fixture for mirror holder to get high surface finish and reduce machining time
  47. Designing of fixture to optimize the manufacturing process of artillery fuse
  48. Enhancing fuse shell production by developing mandrel
  49. Turn-mill process optimization of a complex electronic component
  50. Designing of fixture to optimize the manufacturing process of a mining component
  51. Optimization of manufacturing process plan to increase production rate of thin walled component
  52. Structural analysis and manufacturing process optimization of an aerospace component
  53. Designing fixture to optimization of manufacturing process plan of timer used in war missiles
  54. Reduction of reworks and rejections in manufacturing of a thin walled aerospace component
  55. Modeling & manufacturing of a support component of a dynamic air frame in a missile
  56. 3d model generation for audio amplifier frame by using cad application.
  57. Modeling and manufacturing process plan for fin cage
  58. CNC programme generation of locking pin
  59. Modeling &manufacturing process plan for mother board
  60. Modeling &manufacturing process plan for mounting plate
  61. Modeling &manufacturing process plan for automobile piston
  62. Manufacturing process optimization for secondary mirror support
  63. Modeling &manufacturing process plan for solenoid plunger
  64. Modeling & manufacturing process plan for mirror holder:
  65. CNC program generation for airframe missile
  66. Modeling & CNC programme generation for fuse body
  67. Optimization of manufacturing process for seeker base manufacturing program generation for banjo fitting
  68. 3d model and program generation for gear train by using cam
  69. Modeling and impact of tolerance on manufacturing process for aerospace component:
  70. Multi-axis tool path generation of crank shaft
  71. Modeling, manufacturing and optimization of reworks and rejections of spike support
  72. Modeling & manufacturing process plan generation for pdu mechanical box
  73. Generation of NC program for wing bracket
  74. Modeling & process optimization for bearing stopper
  75. Manufacturing process plan for heater plate
  76. Tool path generation for pulley with flange
  77. CNC programme generation for mount nozzle plate
  78. Development of manufacturing process for pcb end plate
  79. Tool path generation for thin ribbed heat sink
  80. Modeling & manufacturing process plan for satellite camera mounting bracket
  81. Multi-axis tool path generation of rock drill
  82. 3 axis CNC programme generation of cover plate
  83. Modeling & manufacturing process plan for corner bracket
  84. Manufacturing process plan for casing cover plate
  85. CNC programme generation for deckle cover
  86. Generating CNC part program on pru base plate for dmg machine
  87. Generating CNC part program on pru side wall for dmg machine
  88. Modeling & manufacturing of arm right
  89. Manufacturing process optimization of reworks and rejections of missile shield (shell)
  90. Development of manufacturing process plan for booster rocket.

Post Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.